G.SHDSL.bis EFM / TDM Line Card

Previous 6 / 8 Next

G.SHDSL.bis EFM / TDM Line Card Ethernet Access Device Networking Accessories Network Communication Solutions G.SHDSL.bis EFM / TDM Line Card Ethernet Access Device Networking Accessories Network Communication Solutions G.SHDSL.bis EFM / TDM Line Card Ethernet Access Device Networking Accessories Network Communication Solutions G.SHDSL.bis EFM / TDM Line Card Ethernet Access Device Networking Accessories Network Communication Solutions
Quantity
Add Quotation


Description

The G.SHDSL.bis EFM/TDM line card series which takes advantage of the latest G.SHDSL.bis standard, is a mini-terminal enabling the transport of traffic from Ethernet and E1 interface with speed 5.7M/11.4M over EFM bonded 2/4 wires G.SHDSL.bis link.

The G.SHDSL.bis EFM/TDM line card supports high-speed dedicated symmetrical data transmission and utilizes DSL bandwidth. The automatic line rate can be up to 5.7Mbps over 2-wire copper line. To reduce operation/management burden, G.SHDSL.bis EFM/TDM line card within iEAC-16 can control and monitor remote unit via Embedded Operation Channel (EOC) by following ITU-T G.991.2.

Feature

  • Supports EFM and TDM Dual Bearer Mode
  • Point to point Ethernet and E1 extension over multiple G.SHDSL.bis copper lines
  • The interfaces E1 and Ethernet can work simultaneously
  • Compliant with IEEE 802.3ah EFM 2Base-TL bonding technology
  • Compliant with ITU-T G.991.2 standard, TC-PAM 16/32/64/128 line coding
  • 1 or 2 pairs G.SHDSL.bis with 5.7Mbps per pairs Supports extension rate up to 15Mbps over a single pair of copper
  • CO and CPE mode selectable
  • Automatic line rate selection with Line Probe enabled
  • Front panel status LED indicators for easy monitoring
  • Easy installation with console, Telnet, WEB GUI and SNMP
  • Front panel test button with BERT for easy loop diagnostic
  • Provides extensive diagnostics, including loopback, G.SHDSL.bis and E1 performance monitoring
  • Easy software upgrade for field-deployed units via TFTP/HTTP
  • DSL line protection for data transmission
  • Ethernet switching and bridging with VLAN prioritization and QoS
  • Optional temperature-controlled FAN
  • Optional Ethernet port surge protection
  • Supports security-link
  • SNTU765C is a line card type which can work within iEAC-16 chassis 
Specification
Model
  • SNTU765C(Line card), 4-wire, 1 E1 G.703, 1 Ethernet port
Line Interface – G.SHDSL.bis
  • Type: 4-wire
  • Standard: ITU-T G.991.2, ETSI 101 524
  • Bonding protocol: IEEE 802.3ah EFM 2Base-TL
  • Line rate: n x 64Kbps, n=3~89 (2w), 6~178 (4w)
  • Connector: 1xRJ-45
  • Line coding: TC-PAM 16/32/64/128
  • Impedance: 135 ?
  • ITU K.21 compliant
DTE Interface – Ethernet
  • Ethernet type: 10/100 BaseT
  • Connector: RJ-45
  • Supports 802.3x flow control
  • Auto-MDI/MDIX detection
  • Auto-negotiation for speed and duplex
  • Full duplex / Half duplex support
DTE Interface – E1
  • Data Rate: 2.048 Mbps
  • Connector: RJ-45 for balanced E1 120
  • (Optional external convert cable for unbalanced 75)
  • Line coding: HDB3
  • Framing: Framed /Framed+CRC /Unframed
  • Compliance: ITU-T G.703, G.704, G.706 and G.732
  • Jitter Performance: compliant with ITU-T G.823
Timing Source Function
  • Synchronous and Plesiochronous dual clock mode
  • Internal clock
  • Received clock from DSL line
  • External clock from E1 interface
Ethernet L2 function
  • Supports 802.1d transparent bridge function
  • Supports Bridge filter function based on source MAC
  • addresses
  • Scalable per port bandwidth control (Step = 64K, up to 100M)
  • 2K MAC learning address
  • Ethernet packet length up to 1664 bytes
  • Supports 802.3x flow control
  • Provides 802.1q VLAN tagging
  • Supports 802.1p QoS facility
Management
  • Configuration via craft port VT-100, Telnet, WEB GUI and SNMP
  • Multiple Web browsers supported: IE, Firefox, Chrome
  • Console: DB9 connector (RS232C)
  • Support remote management
  • Independent Local and Remote loopback for E1 port diagnostic
  • Support Performance Monitoring function
  • Front panel test button for easy loop healthy testing
  • Front panel reset to default button
LED Indicators
  • SNTU765C:
  • PWR, TST, ALM, DSL, E1, ETH LNK/SPD
  • Dual color LED for easy status monitoring
Dimension
  • 84(W) x 171(D) x 24(H) mm
Operating Environment
  • Operation temperature: 0oC ~ 50oC
  • Storage temperature: -40oC ~ 70oC
  • Humidity: 90%,non-condensing
Application

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Messages*  
   

Switch to Mobile Version
Subscribe Newsletter
1
Hello! Thanks for visiting my site. Please press Start button to Contact with Admin :)

Start